
Must know memory aids for your ATPL exams - PART 2
1. ICET and PCD: from indicated to true airspeed
ICET gives the four airspeeds in order, and PCD gives the error you remove at each step: Indicated, Calibrated, Equivalent, True. The usual phrase is ICE-T is a Pretty Cool Drink. (You may see it written "ICET PDC"; the letters that matter are the order P, then C, then D.)
ICET airspeed chain · 4 speeds, 3 corrections
IAS → CAS, correct for P (instrument and position error): small errors in the instrument itself and in where the pitot tube and static port sit on the airframe. The correction table is in your aircraft's flight manual (POH/AFM).
CAS → EAS, correct for C (compressibility): at high speed the air squashes into the pitot tube and makes the ASI over-read. Below about 200 kt and at low level it is so small that light-aircraft pilots usually ignore it, so for you CAS ≈ EAS.
EAS → TAS, correct for D (density): thinner air at altitude, or in warm conditions, makes the ASI read low. TAS is higher than EAS whenever you are above sea level in the standard atmosphere.
Rule of thumb for light aircraft: TAS is about 2% higher than CAS for every 1,000 ft of altitude. At 5,000 ft with 100 kt CAS, TAS is roughly 110 kt. Use your flight computer for exact figures.
One more step takes you to groundspeed: correct TAS for wind and you get GS, the number you use for timing your navigation legs.
2. PUDSOD: what a blocked pitot or static does to your airspeed
PUDSOD tells you how the airspeed indicator (ASI) lies when a pressure source is blocked: Pitot blocked, Under-reads in Descent; Static blocked, Over-reads in Descent. Learn the descent half, and the climb half is simply the opposite.
The ASI measures the difference between pitot (total) pressure and static pressure. Ask yourself which pressure is trapped and which one is still changing.
Pitot blocked: the pressure in the pitot line is frozen. In a descent the static pressure rises, the difference gets smaller, and the ASI under-reads. The ASI now behaves like an altimeter, which is why it over-reads in a climb.
Static blocked: the static pressure is frozen at the value from the altitude where it blocked. In a descent the real outside pressure rises, the pitot pressure grows against a too-low static, and the ASI over-reads.
With a blocked static port, a descending pilot sees a speed that is too high and may slow down towards the stall. With a blocked pitot in a climb, the rising speed tempts the pilot to pitch up, again towards the stall.
3. UNOS: compass turning errors
In the northern hemisphere, when you turn using the magnetic compass alone you must Undershoot North and Overshoot South. The compass is unreliable in a turn because the Earth's magnetic field dips towards the ground, and banking the aircraft tilts the compass card into that dip.
UNOS on a compass dial · right turns onto North and South
Turning onto North: the compass lags behind the turn. Stop the turn before the compass reaches N, or you will end up turning too far.
Turning onto South: the compass runs ahead of the turn. Keep turning until the compass has gone past S.
East and West: no turning error, so roll out as normal.
How much? At a standard-rate turn the error is roughly equal to your latitude, plus your normal roll-out lead. At about 30° N, as in the picture, that means rolling out around 330° when turning onto North and around 210° when turning onto South.
In the southern hemisphere the dip points the other way, so the rule reverses: overshoot North, undershoot South.
Its partner for acceleration errors is ANDS: on an easterly or westerly heading in the northern hemisphere, Accelerate and the compass shows a turn North, Decelerate and it shows a turn South.
Cheat sheet

Attila Kis
ATPL Course Supervisor
a.kis@easy-pilot.com
